![]() Most video converters can do the conversion including Handbrake and AviDemux. The video may need converting to Constant Frame Rate (CFR) if the difference between the minimum and maximum values are not within ±4 fps of the frame rate. In the Video section of the analysis - if you see this line: Generally mobiles record in Variable Frame Rate (VFR) mode which is known to cause issues in video editors when the minimum and maximum framerates covering a wide range.ĭownload and install MediaInfo and analyse one of the source clips, see this tutorial on how to setup MediaInfo and analyse a video clip for all the data required. The export presets are already optimised for quality vs file size and it is recommended not to change any of the settings. Typically this would be seen as a loss of sharpness, 'blockiness' and banding on subtle colour variations such as a blue sky. However halving the bitrate does create more 'artefacts' as it has less available data per second to encode the video. Rogers LS7 speakers run from Cambridge Audio P50 commented reducing the bitrate does not create motion blur. Ram Acoustic Studio speakers amplified by NAD amplifier. Tuned to room with Tannoy audio application. CS6, NX Studio, Mixcraft 9 Pro.Īudio System 5 x matched bi-wired 150 watt Tannoy Reveal speakers plus one Tannoy 15" 250 watt sub with 5.1 class A amplifier. VXP 14, MEP 2022, Vegas Studio 16, Vegas Pro 18, Cubase 4. M Audio Axiom AIR Mini MIDI keyboard Ver 5. Two Samsung 27" LED SA350 monitors with 5000000:1 contrast ratios at 60Hz. Memory interface 192bit Memory bandwidth 360.o5GB/s 12GB of dedicated GDDR6 video memory, shared system memory 16307MB PCi Express x8 Gen3. Total 16TB of five external WD drives for backup.ĪSUS NVIDIA GeForce RTX 3060 12GB. 1x500GB SSD current project only drive, 1x WD RED 2TB drive for latest footage storage. + x2 WD BLACK 2TB internal SATA 7,200rpm hard drives.1 for internal projects, 1 for Library clips/sounds/music/stills./backup of working projects. Driver version 31.0.101.2125 with 64GB of 3200MHz Corsair DDR4 ram.ġ x 250GB Evo 970 NVMe: drive for C: drive backup 1 x 1TB Sabrent NVMe drive for Operating System / Programs only. Intel i9900K Coffee Lake 3.6 to 5.1GHz CPU with Intel UHD 630 Graphics. Direct X 12.1 latest hardware updates for Western Digital hard drives.Īsus ROG STRIX Z390-F Gaming motherboard Rev 1.xx with Supreme FX inboard audio using the S1220A code. What reducing the file size does is reduce the quality of the export as each frame uses less data and more compression is used which will have the effect of softening the image in general as detail gets merged and lost. Motion blur is solely camera movement and settings generated. Reducing the bit rate does not cause additional motion blur. It will probably read as gobbledygook at first but after an amount of experience in exporting you may eventually get a hang of it. A guide to how to alter these settings can be found at the end of your pdf users manual should you need to tweak a preset. You should export at the same frame rate and resolution of the source files to retain quality. The presets in the Export Movie / Video As **** will give you a drop-down list of preset settings that are good enough for most people but can be played around with if you are not happy with the results. Also setting up wrong settings can produce files with no data or may terminate the export after a while. Each export setting will depend on the bit rates and resolution of the original files so no precise answer can be given if you are super fussy as I am. Beyond a certain point though adding additional bits gives no additional benefit. ![]() This invariably ends with a file larger in data than the original source files creating it. Resolution though is not just the frame size but the bit depth and amount of bits used per pixel to give accurate colour and tonal balance. ![]() Ideally you should export at the same frame rate and resolution as the source files and not mix and match. Sometimes the encoders idea of what is not perceivable is not the same as the editors. Ideally to keep the quality of the encoding high, especially if you have done anything to the files other than cut and butt join them as each frame is read, assessed, and decisions made about what data can be thrown away with no (perceivable) quality loss. You have to realise that each export is a re-encoding and compression of the files being rendered.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |